Differences between revisions 26 and 27
Revision 26 as of 2018-08-10 00:41:19
Size: 2573
Comment:
Revision 27 as of 2018-08-10 00:44:00
Size: 2567
Comment:
Deletions are marked like this. Additions are marked like this.
Line 6: Line 6:
The density of 4% silicon transformer steel is 7.65 g/cm³, so A₁, the cross section of the area M₁, is A₁ = 0.65 cm² = 6.5e-5 m².$~~~$ A₁ = (A-C)×B . The density of 4% silicon transformer steel is 7.65 g/cm³, so A₁, the cross section of the area M₁, is A₁ = 0.65 cm² = 6.5e-5 m².$~~~$ A₁ = (A-C)×R .
Line 14: Line 14:
A fraction C/D of that force is directed upwards for each face; the total upwards force through both faces is F,,C,, = 2 C (A/D)² × 0.16 MPa. Since D² = B² + C², the total downwards deflection force F,,T,, is A fraction C/D of that force is directed upwards for each face; the total upwards force through both faces is F,,C,, = 2 C (A/D)² × 0.16 MPa. Since D² = R² + C², the total downwards deflection force F,,T,, is
Line 16: Line 16:
$$ \Large F_T ~=~ \left( 1 - { { A C } \over { 2 ( B^2 + C^2 ) } } \right) { { A B_{max}^2 } \over { 2 \mu_0 } } $$ $$ \Large F_T ~=~ \left( 1 - { { A C } \over { 2 ( H^2 + C^2 ) } } \right) { { A B_{max}^2 } \over { 2 \mu_0 } } $$
Line 18: Line 18:
This deflects a block of mass with a cross sectional area of (A-C) × B and a mass per unit length of m = ρ × (A-C) × B. The vertical acceleration (which should be maximized for minimum ambit radius) is $~~$ a = F,,T,, / m . This deflects a block of mass with a cross sectional area of (A-C)×R and a mass per unit length of m = ρ×(A-C)×R. The vertical acceleration (which should be maximized for minimum ambit radius) is $~~$ a = F,,T,, / m .

Trapezoid Bolt

attachment:BoltCross.png

The launch loop rotor is composed of separable bolts, mostly made of thin laminations of transformer steel, along with carbon fiber stiffeners, embedded aluminum induction motor conductors, and a central spine. The bolts are normally used in two modes; assembled into a multilobed rotor for the main tracks and inclines, and separated into separate bolts for minimum radius deflection.

The number of lobes in the rotor (and the number of bolts in parallel) remains to be determined; probably between 4 and 6. The length of the bolts may also change. The size and cross section is constrained by the linear density of the rotor.

For a 4.32 kg/m rotor with six lobes, each lobe will mass 7.2 grams per centimeter of length. If 30% of the bolt mass is iron mass M₂, and 70% of the bolt is M₁ then M₁ is approximately 5 g/cm = 5e-3 kg/m.

The density of 4% silicon transformer steel is 7.65 g/cm³, so A₁, the cross section of the area M₁, is A₁ = 0.65 cm² = 6.5e-5 m².~~~ A₁ = (A-C)×R .

Deflection Mode

In deflection mode, an electromagnet pole (shown at the bottom of this diagram) pulls the rotor towards it, with near-saturation flux density B_{max} , perhaps 1.8 Tesla. The material will be strongly saturated and with considerable hysteresis at this field strength; that actually helps regulate the deflection force.

The deflection field "entering" at the bottom exits at the two diagonal pole faces, with less flux density. The (atttracting) deflection force at the bottom is F_A ~=~ A ~×~ B_{max}^2 / 2 \mu_0 so FA = A × 1.29 MPa . The flux at each diagonal face is B_D = ( A / 2 D ) B_{max} so the force at each face is F_D ~=~ D ~×~ B_D^2 / 2 \mu_0 ~=~ D ~×~ (A/2D)^2 B_{max}^2 / 2 \mu_0 ~=~ A^2/D × B_{max}^2 / 8 \mu_0 so FD = A²/D × 0.16 MPa .

A fraction C/D of that force is directed upwards for each face; the total upwards force through both faces is FC = 2 C (A/D)² × 0.16 MPa. Since D² = R² + C², the total downwards deflection force FT is

\Large F_T ~=~ \left( 1 - { { A C } \over { 2 ( H^2 + C^2 ) } } \right) { { A B_{max}^2 } \over { 2 \mu_0 } }

This deflects a block of mass with a cross sectional area of (A-C)×R and a mass per unit length of m = ρ×(A-C)×R. The vertical acceleration (which should be maximized for minimum ambit radius) is ~~ a = FT / m .

MoreLater

TrapezoidBolt (last edited 2018-08-17 22:55:16 by KeithLofstrom)