Differences between revisions 27 and 28
Revision 27 as of 2017-04-13 01:30:32
Size: 3305
Comment:
Revision 28 as of 2017-04-13 01:31:11
Size: 3272
Comment:
Deletions are marked like this. Additions are marked like this.
Line 20: Line 20:
==== Light speed and sound speed ==== ==== Wave equations for a lossless electronic signal cable: ====
Line 22: Line 22:
'''Wave equations for a lossless electronic signal cable:''' $~~~ L C ~ { \Large {{ \partial^2 I } \over { \partial t^2 }} } ~=~ { \Large {{ \partial^2 I } \over { \partial x^2 }} } ~~~~~ L C ~ { \Large {{ \partial^2 V } \over { \partial t^2 }} } ~=~ { \Large {{ \partial^2 V } \over { \partial x^2 }}} $ $~~~ L C ~ { \Large {{ \partial^2 I } \over { \partial t^2 }} } ~=~ { \Large {{ \partial^2 I } \over { \partial x^2 }} } ~~~~~ L C ~ { \Large {{ \partial^2 V } \over { \partial t^2 }} } ~=~ { \Large {{ \partial^2 V } \over { \partial x^2 }}} $

Acoustic Climber for Space Elevator

THe current reference space elevator design assumes solar-powered climbers. This assumes that vast areas of solar panels can cantilever from the sides of a climber - in gravity - and provide megawatts of climb power, while being lightweight and affordable. The example pictured is a DLR solar sail, intended for microgravity, NOT an array of solar cells. Solar sails are ultrathin plastic films covered with just enough shiny metal to reflect light. Aluminum conductivity is 2.8e-8 ohm/meter; a film with 10 ohm per square resistivity (95% reflective) is 2.8e-9 meters thick - a few atomic layers. The density is 2700 kg per cubic meter, works out to 8 kilograms per square kilometer on top of the plastic. This is far less than actual satellite solar panels (300 W/m2, 1 kg/m2), which are designed for microgravity, not to deploy in a gravity field. These arrays are stabilized by gravitational gradients in orbit, and they are test-deployed on the ground hanging sideways from heavy structure.

Instead, a superstrong tether can carry megawatts of subkilohertz acoustic power, which can be impedance-matched and mechanically rectified (mad handwaving here) to produce climber thrust. The acoustic transmitters on the ground and at GEO node can provide 2 MW and 10 MW of climb power respectively, more by trading off climber mass, gravitational weight, and climber speed. Climbers will have a mechanical receiver that transforms vibration to rotary wheel motion.

A preliminary paper

That's the old stuff. This is morphing into a pair of low inertia electrical motors separated by a quarter wave, with electrical power conversion at each motor, with power cable and stiff tether between.


Analogy Between an Electronic Signal Cable and a Stiff Tether

All units MKS: meters, kilograms, seconds, volts, amperes (amps), radians

( FYI: if you don't think radians are a unit, you are turned around, and can't distinguish energy from torque. :-? )

==== Wave equations for a lossless electronic signal cable: ====

~~~ L C ~ { \Large {{ \partial^2 I } \over { \partial t^2 }} } ~=~ { \Large {{ \partial^2 I } \over { \partial x^2 }} } ~~~~~ L C ~ { \Large {{ \partial^2 V } \over { \partial t^2 }} } ~=~ { \Large {{ \partial^2 V } \over { \partial x^2 }}}

  • C = capacitance per unit length, farads per meter

  • L = inductance per unit length, henrys per meter

Sinusoidal solutions (many others are possible): ~~~I = I_0 \sin( \omega t + k x ) amps ~~~~~ V = V_0 \sin( \omega t + k x ) volts

  • frequency ~ \omega ~ ~ radians per second

  • wavenumber ~ k ~ = ~ \pm \sqrt{ L C } ~ \omega ~ ~ radians per meter

  • speed ~ v ~ = ~ \omega / k ~ = ~ \pm 1 / \sqrt{ L C } ~ ~ in the +x or -x direction, a large fraction of the speed of light

    • a function of the materials used, typically around 0.5c or 150 million meters per second

  • impedance ~ Z ~ = ~ \sqrt{ L / C } ~ = ~ V_0 / I_0 ~ ~ ohms

    • a function of the materials used and cross section, typically around 50 ohms but can be higher than 100 ohms and lower than 10 ohms
  • MoreLater


AcousticClimber (last edited 2017-10-05 03:46:10 by KeithLofstrom)